Later releases have switched over to snprintf to avoid this issue, but 14.11
did not get that patch. Bug 2295.

_slurm_rpc_complete_job_allocation.

This is a rewrite of 438365ec which didn't catch the job_ptr wasn't
in a lock so the memory issue could still of existed.  This hopefully fixes
all the spots the job_ptr wasn't in the lock.

Fixes bug 2146

the Steps keyword.

Bug 2095

database but the start record hadn't made it yet.

bug 2011

','.

bug 1999

Don't requeue RPC going out from slurmctld to DOWN nodes (can generate
    repeating communication errors).
bug 2002

This will only happen if a PING RPC for the node is already queued
  when the decision is made to power it down, then fails to get
  a response for the ping (since the node is already down).
bug 1995

If a job's CPUs/task ratio is increased due to configured MaxMemPerCPU,
then increase it's allocated CPU count in order to enforce CPU limits.
Previous logic would increase/set the cpus_per_task as needed if a
job's --mem-per-cpu was above the configured MaxMemPerCPU, but NOT
increase the min_cpus or max_cpus varilable. This resulted in allocating
the wrong CPU count.

Requeue/hold batch job launch request if job already running. This is
  possible if node went to DOWN state, but jobs remained active.
In addition, if a prolog/epilog failed DRAIN the node rather than
  setting it down, which could kill jobs that could continue to
  run.
bug 1985

Bug 1938

Bug 1984

When nodes have been allocated to a job and then released by the
  job while resizing, this patch prevents the nodes from continuing
  to appear allocated and unavailable to other jobs. Requires
  exclusive node allocation to trigger. This prevents the previously
  reported failure, but a proper fix will be quite complex and
  delayed to the next major release of Slurm (v 16.05).
bug 1851

The 2 came from the nodelist being "None assigned", which would be treated
as 2 hosts when sent into hostlist.

Correct counting for job array limits, job count limit underflow possible
    when master cancellation of master job record.
bug 1952

only 1 job was accounted (against MaxSubmitJob) for when an array was
submitted.

This prevents a step from being launched if the job is killed
while the prolog is running. Reproducing the original failure
requires use of srun to trigger the prolog and using scancel
while that prolog is running.
bug 1755

And add missing documenation.
Bug 1921

GRES were not being properly tracks for multiple simultaneous steps.
A step which could have run later could be rejected as never being
able to run.
Replacement for commit dd842d79, which was reverted in commit 6f73812875c
bug 1925

and you use all the GRES up instead of reporting the configuration isn't
available you hold the requesting step until the GRES is available.

Don't trucate task ID information in "squeue --array/-r" output.
Task ID info in sview also expanded to 64 characters (from ~16 chars).

Previous logic would set the avail_node_bitmap when
a node was powered down, even if the initial state was
DOWN or DRAINED. This made the node available for allocation
to a job, which we don't want until the DOWN or DRAIN
state is cleared.
bug 1893

This reverts commits
7660da9e
5c386455 and
f6c5302b

Bug 1741

This problem is reproducible by launching a job then killing the
  slurmstepd process. Under those conditions, requeue the job if
  possible (i.e. batch job with requeue option/configuration).
  This patch also improves the slurmctld logging when this happens.
bug 1889

Correct RebootProgram logic when executed outside of a maintenance
  reservation. Previous logic would mark the node up upon response
  to the reboot RPC (from slurmctld to slurmc) and when the node
  actually rebooted, flag that as an unexpected reboot. This new
  logic checks the node's up time to not mark the compute node as
  being usable until the reboot actually takes place.
but 1866