Require SchedulerTimeSlice configuration parameter to be at least 5 seconds
to avoid thrashing slurmd daemon.
Addresses Cray bug 774692

Change in GRES behavior for job steps: A job step's default generic
    resource allocation will be set to that of the job. If a job step's --gres
    value is set to "none" then none of the generic resources which have been
    allocated to the job will be allocated to the job step.
Add srun environment value of SLURM_STEP_GRES to set default --gres value
    for a job step.

On Bluegene systems, smap's command-line mode would generate an invalid
memory reference due to an uninitialized variable.

a POLLERR the dbd_fail callback is called.

the DBD where both remained up but were disconnected the slurmctld would
get registered again with the DBD.

With sched/wiki or sched/wiki2 (Maui or Moab scheduler), insure that a
requeued job's priority is reset to zero.

Add the ability for a user to limit the number of leaf switches in a job's
allocation using the --switch option of salloc, sbatch and srun. There is
also a new SchedulerParameters value of max_switch_wait, which a SLURM
administrator can used to set a maximum job delay and prevent a user job
from blocking lower priority jobs for too long. Based on work by Rod
Schultz, Bull.

BlueGene: Permit users to specify a separate connection type for each
dimension (e.g. "--conn-type=torus,mesh,torus").

On Cray systems with the srun2aprun wrapper, build an srun man page
that describes which options are available with the wrapper.

Restore node configuration information (CPUs, memory, etc.) for powered
down when slurmctld daemon restarts rather than waiting for the node to be
restored to service and getting the information from the node (NOTE: Only
relevent if FastSchedule=0).

Fix bug in select/cons_res task distribution logic when tasks-per-node=0.
Eliminates misleading slurmctld message
"error:  cons_res: _compute_c_b_task_dist oversubscribe."
This problem was introduced in SLURM version 2.2.5 in order to fix
a task distribution problem when cpus_per_task=0. Patch from Rod Schultz, Bull.

Set SLURM_MEM_PER_CPU or SLURM_MEM_PER_NODE environment variables for both
interactive (salloc) and batch jobs if the job has a memory limit. For Cray
systems also set CRAY_AUTO_APRUN_OPTIONS environment variable with the
memory limit.

For front-end configurations (Cray and IBM BlueGene), bind each batch job to
a unique CPU to limit the damage which a single job can cause. Previously any
single job could use all CPUs causing problems for other jobs or system
daemons. This addresses a problem reported by Steve Trofinoff, CSCS.

man pages. Patch by Nancy Kritkausky, Bull.

Bill Brophy, Bull.

Note the job and partition state file formats have changed and RPCs
with information for jobs and partitions have changed.

Fix bug in generic resource tracking of gres associated with specific CPUs.
Resources were being over-allocated.

Fix memory buffering bug if a AllowGroups parameter of a partition has 100
or more users. Patch by Andriy Grytsenko (Massive Solutions Limited).

Add cgroup support for device files in both the task/cgroup plugin and generic
resource (GRES) logic. Based upon patch Yiannis Georgiou.

When suspending a job, wait 2 seconds instead of 1 second between sending
SIGTSTP and SIGSTOP. Some MPI implementation were not stopping within the
1 second delay.

Add contribs/arrayrun tool providing support for job arrays. Contributed by
Bjørn-Helge Mevik, University of Oslo. NOTE: Not currently packaged as RPM
and manual file editing is required.

If a job needed to preempt other jobs to start and those jobs were
not completed by the time of the next scheduling cycle, other jobs
might be selected for preemption in that next cycle resulting in
more jobs being preempted than necessary.

Previous logic reported the run time as the current time minus the job start time,
ignoring any suspended time.

Enhancements to sched/backfill performance with select/cons_res plugin.
Major improvements would be seen with large job counts. Based upon
bf_build_row_bitmaps_2.2.6.patch patch from Bjørn-Helge Mevik, University of Oslo.

association limit.

Add default and maximum memory limits on a per-partitiion basis. If not
specified, the system-wide memory limits will apply.

Add select_jobinfo to the task launch RPC so that all nodes have access to
the information and not job the head node.  Based upon patch by Andriy
Grytsenko (Massive Solutions Limited).

Fix possible invalid memory reference in sched/backfill. Patch by Andriy
Grytsenko (Massive Solutions Limited).

Add flag to the select APIs for job suspend/resume indicating if the action
is for gang scheduling or an explicit job suspend/resume by the user. Only
an explicit job suspend/resume will reset the job's priority and make
resources exclusively held by the job available to other jobs. This change
is also needed for Cray systems with ALPS.

Add squeue support to display a job's license information. Patch by Andy
Roosen (University of Deleware).

For front-end architectures on which job steps are run (emulated Cray and
BlueGene systems only), fix bug that would free memory still in use.

Processes suspended and resumed are determined by using process group ID
and parent process ID, so some processes may be missed. Since salloc runs
as a normal user, it's ability to identify processes associated with a job
is limited.

Improve efficiency of select/linear plugin with topology/tree plugin
configured, Patch by Andriy Grytsenko (Massive Solutions Limited).

Modify smap and sview to display all nodes even if multiple
nodes exist at each coordinate.

Cray systems: Add support to suspend/resume salloc command to insure that
aprun does not get initiated when the job is suspended.

With regard to forthcoming Accelerator support in Basil 1.2/Alps 4.0, this adds
interface support for passing the following Accelerator parameters:
 * accelerator type (currently only "GPU" is supported),
 * model/rank information (uninterpreted "family" string),
 * amount of on-board memory in MB.
02_Cray-Accelerator-params.diff
Patch from Gerrit Renker and Stephen Trofinoff, CSCS.

This adds support to parse Basil 1.2/Alps 4.0 per-node accelerator information.
01_Cray-Accelerator-basic-support.diff
Patch from Gerrit Renker and Stephen Trofinoff, CSCS