Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Boris Karasev <karasev.b@gmail.com>

- Remove debug leftover that was causing undeleted temp directories
- Fix compiler warnings

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

- fix I/O engine finalization order.
- _send_progress may be called when I/O engine it's not yet operating.
- fix I/O engine message queues management

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Latency results:
1       0.000079
2       0.000082
4       0.000078
8       0.000084
16      0.000084
32      0.000083
64      0.000091
128     0.000100
256     0.000113
512     0.000125
1024    0.000177
2048    0.000427
4096    0.000514
8192    0.000522
16384   0.000590
32768   0.000872
65536   0.001745
131072  0.002758
262144  0.004833
524288  0.009263
1048576 0.018100
2097152 0.036140
4194304 0.071862

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Since we setting TCP_NODELAY option on the socket, data is not
buffered anymore. This means that original approach that assumes
that we write the header and then move to the message payload
will result in 2 TCP messages instead desired one.

This commit uses writev to enable atomic non-contiguous data send.

Latency:
1       0.000084
2       0.000112
4       0.000109
8       0.000107
16      0.000102
32      0.000101
64      0.000102
128     0.000114
256     0.000119
512     0.000134
1024    0.000173
2048    0.000411
4096    0.000517
8192    0.000526
16384   0.000587
32768   0.000894
65536   0.001694
131072  0.002778
262144  0.004981
524288  0.009312
1048576 0.018522
2097152 0.036365
4194304 0.072543

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Use TCP_NODELAY to solve performance overhead.

Latency results for direct TCP connections:
(small message latency significantly improved)
1       0.000244
2       0.000238
4       0.000239
8       0.000238
16      0.000237
32      0.000240
64      0.000250
128     0.000252
256     0.000250
512     0.000254
1024    0.000335
2048    0.000327
4096    0.000530
8192    0.000540
16384   0.000576
32768   0.000953
65536   0.001634
131072  0.002767
262144  0.004726
524288  0.009316
1048576 0.018161
2097152 0.036179
4194304 0.071893

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Add some developer code that will allow to measure the latency of
the communication subsystem used.

Here is initial results for existing communication options:

Environment:
SLURM_PMIX_DIRECT_CONN=[true | false]
SLURM_PMIX_TIMEOUT=1000000
SLURM_PMIX_WANT_PP=1
SLURM_PMIX_PP_LOW_PWR2=0
SLURM_PMIX_PP_UP_PWR2=22
SLURM_PMIX_PP_ITER_SMALL=100
SLURM_PMIX_PP_ITER_LARGE=20

Launch cmdline:
$ srun --mpi=pmix -N2 -n2 sleep 10000

SLURM RPC results:
1       0.000669
2       0.000669
4       0.000669
8       0.000659
16      0.000668
32      0.000664
64      0.000668
128     0.000661
256     0.000668
512     0.000692
1024    0.000776
2048    0.000750
4096    0.000743
8192    0.000819
16384   0.001230
32768   0.001385
65536   0.002137
131072  0.003798
262144  0.006664
524288  0.011702
1048576 0.021605
2097152 0.042588
4194304 0.084673

Direct TCP connections
(better for large messages, but not yet for small):
1       0.078999
2       0.078999
4       0.078999
8       0.078999
16      0.078999
32      0.078999
64      0.079000
128     0.078999
256     0.079000
512     0.079000
1024    0.078998
2048    0.000409
4096    0.000639
8192    0.000521
16384   0.000618
32768   0.000933
65536   0.001622
131072  0.002749
262144  0.004704
524288  0.009281
1048576 0.018133
2097152 0.036172
4194304 0.071875

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

- SLURM protocol is used to initiate communication and
  deliver sender's TCP port number to the receiver.
- After the first message is received all communication
  goes through the direct TCP connections.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

- Introduce nitation of endpoint to distinguish between
  broadcast and point-to-point exchanges.
- Fix magic number naming: change all PMIX_ prefixes to PMIXP_
  to avoid conflicts with PMIx library macroses.
- Fix I/O engine cleanup logic as now I/O engines are used more
  than once.
- make a namespace subsystem to return xmalloc'd pointers as opposed
  to malloc'd to avoid confusion as everything else is xmallox'd.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

- Introduce data structures reuse to avoid extra malloc/free overhead.
- Introduce direct TCP connection notation (disabled for now)

This commit is intended for testing SLURM protocol portion of the code
to see that nothing is broken.
Direct communication will be enabled in the next commit.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

- Provide ability to initialize I/O engine without knowing fd this will
be used when we will be sending connection request using SLURM protocol
and queuing all other send's waiting for connection to be established.
- Simplify some I/O API and I/O internals.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

- sort out API: headers and callbacks
- Change "pmix_" prefix to "pmixp_" for previously unused send functions.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Remove "health check" functionality as it is not needed.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

This field is a stub for now, but will be used to pass the port number
where corresponding stepd is listening for incoming connections.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

- fix some function names
- separate generic I/O from the slurm protocol specific.

Signed-off-by: Artem Polyakov <artpol84@gmail.com>

Coverity CID 45177

Coverity, CID 44795

Coverity CID 171452

All of these were pre-existing Coverity errors, but I changed nearby
code, variable names, etc. so they looked like new errors.

Coverity reported problem, CID 45194

CID 44936

Coverity CID 171494

variables

This restores perl API operation after commit aea2f0e2

Bug 3956.