NEWS

This file describes changes in recent versions of SLURM. It primarily
documents those changes that are of interest to users and admins.

* Changes in SLURM 2.1.0-pre5
=============================
 -- Add squeue option "--start" to report expected start time of pending jobs.
 -- Sched/backfill plugin modified to set expected start time of pending jobs.
 -- Add SchedulerParameters option of "max_job_bf=#" to control how far down
    the queue of pending jobs that SLURM searches in an attempt backfill 
    schedule them. The default value is 50 jobs.
 -- Fixed cause of squeue -o "%C" seg fault.
 -- Add -"-signal=<int>@<time>" option to salloc, sbatch and srun commands to
    notify programs before reaching the end of their time limit.
 -- Add scontrol option to update a running job's EndTime (also resets the 
    job's time limit).
 -- Add new job wait reason, ReqNodeNotAvail: Required node is not available 
    (down or drained).
 -- Log when slurmctld or slurmd are started with small core file limit.
 -- Permit job's owner to change features, processor count, minimum and 
    maximun node counts of pending jobs (the operation was previously 
    restricted to user root)
 -- Applied patch from Chuck Clouston for scontrol man page with clarifications
    and additional info
 -- Change slurm errno name from ESLURM_TOO_MANY_REQUESTED_NODES to 
    ESLURM_INVALID_NODE_COUNT to better reflect its meaning.
 -- Fix bug in sched/backfill which could result in invalid memory reference
    when trying to schedule jobs submitted with --exclude option.
 -- Fix for slurmctld deadlock at startup with PreemptMode=SUSPEND,GANG.
 -- Added preemptition plugins to RPM.
 
* Changes in SLURM 2.1.0-pre4
=============================
 -- Move processing of node configuration information in slurm.conf and 
    topology information in topology.conf from slurmctld into common and load 
    that information into slurmd. Use it to set environment variables for jobs
    SLURM_TOPOLOGY_ADDR and SLURM_TOPOLOGY_ADDR_PATTERN describing the network
    topology for each task. Based upon patch from Mattheu Hautreux (CEA).
 -- Correction in computing a job's TotalProcs value when ThreadsPerCore>1 and
    allocating by cores or sockets.

* Changes in SLURM 2.1.0-pre3
=============================
 -- Removed sched/gang plugin and moved the logic directly into the slurmctld
    daemon so that job preemption and gang scheduling can be used with the
    sched/backfill plugin. Added configuration parameter:
    PreemptMode=gang|off|suspend|cancel|requeue|checkpoint 
    to enable/disable gang scheduling and job preemption logic (both are 
    disabled by default).
    (NOTE: There are some problems with memory management which could prevent a
    job from starting when memory would be freed by a job being requeued or 
    otherwise removed, these are being worked on)
 -- Added PreemptType configuration parameter to identify preemptable jobs.
    Former users of SchedType=sched/gang should set SchedType=sched/backfill,
    PreemptType=preempt/partition_prio and PreemptMode=gang,suspend. See
    web and slurm.conf man page for other options.
    PreemptType=preempt/qos uses Quality Of Service information in database.
 -- In select/linear, optimize job placement across partitions.
 -- If the --partition option is used with the sinfo or squeue command then
    print information about even hidden partitions.
 -- Replaced misc cpu allocation members in job_info_t with select_job_res_t
    which will only be populated when requested (show_flags & SHOW_DETAIL)
 -- Added a --detail option to "scontrol show job" to display the cpu/mem
    allocation info on a node-by-node basis.
 -- Added logic to give correct request uid for individual steps that 
    were cancelled.
 -- Created a spank_get_item() option (S_JOB_ALLOC_MEM) that conveys the memory
    that the select/cons_res plugin has allocated to a job.
 -- BLUEGENE - blocks in error state are now handled correctly in accounting.
 -- Modify squeue to print job step information about a specific job ID using
    the following syntax: "squeue -j <job_id> -s".
 -- BLUEGENE - scontrol delete block and update block can now remove blocks 
    on dynamic laid out systems.
 -- BLUEGENE - Vastly improve Dynamic layout mode algorithm.
 -- Address some issues for SLURM support of Solaris.
 -- Applied patch from Doug Parisek (Doug.Parisek@bull.com) for speeding up 
    start of sview by delaying to creation of tooltips until requested.
 -- Changed GtkToolTips to GtkToolTip for newer versions of GTK.
 -- Applied patch from Rod Schultz (Rod.Schultz@Bull.com) that eliminates
    ambiguity in the documentation over use of the terms "CPU" and "socket".
 -- Modified get_resource_arg_range() to return full min/max values when input
    string is null.  This fixes the srun -B option to function as documented.
 -- If the job, node, partition, reservation or trigger state file is missing 
    or too small, automatically try using the previously saved state (file 
    name with ".old" suffix).
 -- Set a node's power_up/configuring state flag while PrologSlurmctld is
    running for a job allocated to that node.
 -- If PrologSlurmctld has a non-zero exit code, requeue the job or kill it.
 -- Added sacct ability to use --format NAME%LENGTH similar to sacctmgr.
 -- Improve hostlist logic for multidimensional systems.
 -- The pam_slurm Pluggable Authentication Module for SLURM previously
    distributed separately has been moved within the main SLURM distribution
    and is packaged as a separate RPM.
 -- Added configuration parameter MaxTasksPerNode.
 -- Remove configuration parameter SrunIOTimeout.
 -- Added functionality for sacctmgr show problems.  Current problems include
    Accounts/Users with no associations, Accounts with no users or subaccounts
    attached in a cluster, and Users with No UID on the system.
 -- Added new option for sacctmgr list assoc and list cluster WOLimits.  This 
    gives a smaller default format without the limit information.  This may 
    be the new default for list assocations and list clusters.
 -- Users are now required to have an association with there default account.
    Sacctmgr will now complain when you try to modify a users default account
    which they are not associated anywhere.
 -- Fix select/linear bug resulting in run_job_cnt underflow message if a 
    suspended job is cancelled.
 -- Add test for fsync() error for state save files. Log and retry as needed.
 -- Log fatal errors from slurmd and slurmctld to syslog.
 -- Added error detection and cleanup for the case in which a compute node is 
    rebooted and restarts its slurmd before its "down" state is noticed.
 -- BLUEGENE systems only - remove vestigal start location from jobinfo.
 -- Add reservation flag of "OVERLAP" to permit a new reservation to use
    nodes already in another reservation.
 -- Fix so "scontrol update jobid=# nice=0" can clear previous nice value.
 -- BLUEGENE - env vars such as SLURM_NNODES, SLURM_JOB_NUM_NODES, and
    SLURM_JOB_CPUS_PER_NODE now reference cnode counts instead of midplane
    counts.  SLURM_NODELIST still references midplane names.
 -- Added qos support to salloc/sbatch/srun/squeue
 -- Added to scancel the ability to select jobs by account and qos
 -- Recycled the "-A" argument indicate "account" for all the commands that
    accept the --account argument (srun -A to allocate is no longer supported.)
 -- Change sbatch response from "sbatch: Submitted batch job #" written to 
    stderr to "Submitted batch job #" written to stdout.
 -- Made shutdown and cleanup a little safer for the mvapich and mpich1_p4
    plugins.
 -- QOS support added with limits, priority and preemption
    (no documentation yet).
 -- If a slurmd does not have a node listed in it's slurm.conf (slurm.conf's 
    should be kept the same on all nodes) an error message is printed in the 
    slurmctld log along with the message already being printed in the slurmd 
    log for easier debugging.

* Changes in SLURM 2.1.0-pre2
=============================
 -- Added support for smap to query off node name for display.
 -- Slurmdbd modified to set user ID and group ID to SlurmUser if started as 
    user root.
 -- Configuration parameter ControlMachine changed to  accept multiple comma-
    separated hostnames for support of some high-availability architectures.
 -- ALTERED API CALL slurm_get_job_steps 0 has been changed to NO_VAL for both
    job and step id to recieve all jobs/steps.  Please make adjustments to
    your code.
 -- salloc's --wait=<secs> option deprecated by --immediate=<secs> option to 
    match the srun command.
 -- Add new slurmctld list for node features with node bitmaps for simplified
    scheduling logic.
 -- Multiple features can be specified when creating a reservation. Use "&" 
    (AND) or "|" (OR) separators between the feature names.
 -- Changed internal node name caching so that front-end mode would work with
    multiple lines of node name definitions. 
 -- Add node state flag for power-up/configuring. Represented by "#" suffix
    on the node state name (e.g. "ALLOCATED#") for command output.
 -- Add CONFIGURING/CF job state flag for node power-up/configuring.
 -- Modify job step cancel logic for scancel and srun (on reciept of SIGTERM 
    or three SIGINT) to immediately send SIGKILL to spawned tasks.  Previous 
    logic would send SIGCONT, SIGTERM, wait KillWait seconds, SIGKILL.
 -- Created a spank_get_item() option (S_JOB_ALLOC_CORES) that conveys the cpus
    that the select/cons_res plugin has allocated to a job.
 -- Improve sview performance (outrageously) on very large machines.
 -- Add support for licenses in resource reservation.
 -- BLUEGENE - Jobs waiting for a block to boot will now be in Configuring
    state. 
 -- bit_fmt now does not return brackets surrounding any set of data.

* Changes in SLURM 2.1.0-pre1
=============================
 -- Slurmd notifies slurmctld of node boot time to better clean up after node
    reboots.
 -- Slurmd sends node registration information repeatedly until successful
    transmit.
 -- Change job_state in job structure to dedicate 8-bits to state flags. 
    Added macros to get state information (IS_JOB_RUNNING(job_ptr), etc.)
 -- Added macros to get node state information (IS_NODE_DOWN(node_ptr), etc).
 -- Added support for Solaris. Patch from David Hoppner.
 -- Rename "slurm-aix-federation-<version>.rpm" to just 
    "slurm-aix-<version>.rpm" (federation switch plugin may not be present).
 -- Eliminated the redundant squeue output format and sort options of 
    "%o" and "%b". Use "%D" and "%S" formats respectively. Also eliminated 
    "%X" and "%Y" and "%Z" formats. Use "%z" instead.
 -- Added mechanism for SPANK plugins to set environment variables for
    Prolog, Epilog, PrologSLurmctld and EpilogSlurmctld programs using
    the functions spank_get_job_env, spank_set_job_env, and 
    spank_unset_job_env. See "man spank" for more information.
 -- Completed the work to begun in 2.0.0 to standardize on using '-Q' as the
    --quiet flag for all the commands.
 -- BLUEGENE - sinfo and sview now display correct cpu counts for partitions
 -- Cleaned up the cons_res plugin.  It now uses a ptr to a part_record
    instead of having to do strcmp's to find the correct one.
 -- Pushed most all the plugin specific info in src/common/node_select.c 
    into the respected plugin.
 -- BLUEGENE - closed some corner cases where a block could had been removed 
    while a job was waiting for it to become ready because an underlying 
    part of the block was put into an error state.
 -- Modify sbcast logic to prevent a user from moving files to nodes they
    have not been allocated (this would be possible in previous versions
    only by hacking the sbcast code).
 -- Add contribs/sjstat script (Perl tool to report job state information).
    Put into new RPM: sjstat.
 -- Add sched/wiki2 (Moab) JOBMODIFY command support for VARIABLELIST option
    to set supplemental environment variables for pending batch jobs.
 -- BLUEGENE - add support for scontrol show blocks.
 -- Added support for job step time limits.

* Changes in SLURM 2.0.6
========================
 -- Fixed seg fault when "scontrol listpids" is invoked for a specific job step
    on a node on which a stepd is not running.
 -- Fix bug in sched/backfill which could result in invalid memory reference 
    when trying to schedule jobs submitted with --exclude option.

* Changes in SLURM 2.0.5
========================
 -- BLUEGENE - Added support for emulating systems with a X-dimension of 4.
 -- BLUEGENE - When a nodecard goes down on a non-Dynamic system SLURM will 
    now only drain blocks under 1 midplane, if no such block exists then SLURM 
    will drain the entire midplane and not mark any block in error state.  
    Previously SLURM would drain every overlapping block of the nodecard 
    making it possible for a large block to make other blocks not work since 
    they overlap some other part of the block that really isn't bad.
 -- BLUEGENE - Handle L3 errors on boot better.
 -- Don't revoke a pending batch launch request from the slurmctld if the
    job is immediately suspended (a normal event with gang scheduling).
 -- BLUEGENE - Fixed issue with restart of slurmctld would allow error block 
    nodes to be considered for building new blocks when testing if a job would 
    run.  This is a visual bug only, jobs would never run on new block, but 
    the block would appear in slurm tools.
 -- Better responsiveness when starting new allocations when running with the 
    slurmdbd.
 -- Fixed race condition when reconfiguring the slurmctld and using the 
    consumable resources plugin which would cause the controller to core.
 -- Fixed race condition that sometimes caused jobs to stay in completing
    state longer than necessary after being terminated.
 -- Fixed issue where if a parent account has a qos added and then a child
    account has the qos removed the users still get the qos.
 -- BLUEGENE - New blocks in dynamic mode will only be made in the system
    when the block is actually needed for a job, not when testing.
 -- BLUEGENE - Don't remove larger block used for small block until job starts.
 -- Add new squeue output format and sort option of "%L" to print a job's time 
    left (time limit minus time used).
 -- BLUEGENE - Fixed draining state count for sinfo/sview.
 -- Fix for sview to not core when viewing nodes allocated to a partition 
    and the all jobs finish.
 -- Fix cons_res to not core dump when finishing a job running on a 
    defunct partition.
 -- Don't require a node to have --ntasks-per-node CPUs for use when the 
    --overcommit option is also used.
 -- Increase the maximum number of tasks which can be launched by a job step
    per node from 64 to 128. 
 -- sview - make right click on popup window title show sorted list.
 -- scontrol now displays correct units for job min memory and min tmp disk.
 -- better support for salloc/sbatch arbitrary layout for setting correct 
    SLURM_TASKS_PER_NODE
 -- Env var SLURM_CPUS_ON_NODE is now set correctly depending on the 
    FastSchedule configuration parameter.
 -- Correction to topology/3d_torus plugin calculation when coordinate value 
    exceeds "9" (i.e. a hex value).
 -- In sched/wiki2 - Strip single and double quotes out of a node's reason 
    string to avoid confusing Moab's parser.
 -- Modified scancel to cancel any pending jobs before cancelling any other
 -- Updated sview config info
 -- Fix a couple of bugs with respect to scheduling with overlapping 
    reservations (one with a flag of "Maintenance").
 -- Fix bug when updating a pending job's nice value after explicitly setting
    it's priority.
 -- We no longer add blank QOS'
 -- Fix task affinity for systems running fastschedule!=0 and they have less 
    resources configured than in existence.
 -- Slurm.pm loads without warning now on AIX systems
 -- modified pmi code to do strncpy's on the correct len
 -- Fix for filling in a qos structure to return SLURM_SUCCESS on success.
 -- BLUEGENE - Added SLURM_BG_NUM_NODES with cnode count of allocation, 
    SLURM_JOB_NUM_NODES represents midplane counts until 2.1.
 -- BLUEGENE - Added fix for if a block is in error state and the midplane 
    containning the block is also set to drain/down.  This previously 
    prevented dynamic creation of new blocks when this state was present.
 -- Fixed bug where a users association limits were not enforced, only 
    parent limits were being enforced.
 -- For OpenMPI use of SLURM reserved ports, reserve a count of ports equal to 
    the maximum task count on any node plus one (the plus one is a correction).
 -- Do not reset SLURM_TASKS_PER_NODE when srun --preserve-env option is used
    (needed by OpenMPI).
 -- Fix possible assert failure in task/affinity if a node is configured with
    more resources than physically exist.
 -- Sview can now resize columns.
 -- Avoid clearing a drained node's reason field when state is changed from
    down (i.e. returned to service). Note the drain state flag stays set.

* Changes in SLURM 2.0.4
========================
 -- Permit node suspend/resume logic to be enabled through "scontrol reconfig"
    given appropriate changes to slurm configuration file.
 -- Check for return codes on functions with warn_unused_result set.
 -- Fix memory leak in getting step information (as used by squeue -s).
 -- Better logging for when job's request bad output file locations.
 -- Fix issue where if user specified non-existant file to write to slurmstepd
    will regain privileges before sending batch script ended to the controller.
 -- Fix bug when using the priority_multifactor plugin with no associations 
    yet.
 -- BLUEGENE - we no longer check for the images to sync state.  This was 
    needed long ago when rebooting blocks wasn't a possibility and should 
    had been removed when that functionality was available.
 -- Added message about no connection with the database for sacctmgr.
 -- On BlueGene, let srun or salloc exit on SIGINT if slurmctld dies while
    booting its block.
 -- In select/cons_res fix bug that could result in invalid memory pointer
    if node configurations in slurm.conf contains 8 or more distinct 
    socket/core/thread counts.
 -- Modify select/cons_res to recognize updated memory size upon node startup
    if FastSchedule=0.
 -- Fixed bug if not enforcing associations, but running with them and the 
    priority/multifactor, the slurmctld will not core dump on processing usage.
 -- QOS will not be reset to the default when added back a previously deleted
    association.
 -- Do not set a job's virtual memory limit based upon the job's specified
    memory limit (which should be a real memory limit, not virtual).
 -- BLUEGENE - fix for sinfo/sview for displaying proper node count for nodes 
    in draining state.
 -- Fix for sview when viewing a certain part of a group (like 1 job) so it 
    doesn't core when the part is gone.
 -- BLUEGENE - Changed order of SYNC's to be on the front of the list to
    avoid having a job terminated with a TERM before the SYNC of the 
    job happens.
 -- Validate configured PluginDir value is a valid directory before trying to
    use it.
 -- Fix to resolve agent_queue_request symbol from some checkpoint plugins.
 -- Fix possible execve error for sbatch script read from stdin.
 -- Modify handling of user ID/name and group ID/name in the slurm.conf file
    to properly handle user names that contain all digits. Return error code 
    from uid_from_string() and gid_from_string() functions rather than a uid of
    -1, which might be a valid uid or gid on some systems.
 -- Fix in re-calcuation of job priorities due to DOWN or DRAINED nodes.

* Changes in SLURM 2.0.3
========================
 -- Add reservation creation/update flag of Ignore_Jobs to enable the creation
    of a reservation that overlaps jobs expected to still be running when
    the reservation starts. This would be especially useful to reserve all 
    nodes for system maintenence without adjusting time limits of running
    jobs before creating the reservation. Without this flag, nodes allocated
    jobs expected to running when the reservation begins can not be placed 
    into a reservation.
 -- In task/affinity plugin, add layer of abstraction to logic translating
    block masks to physical machine masks. Patch from Matthieu Hautreux, CEA.
 -- Fix for setting the node_bitmap in a job to NULL if the job does not 
    start correctly when expected to start.
 -- Fixed bug in srun --pty logic. Output from the task was split up 
    arbitrarily into stdout and stderr streams, and sometimes was printed 
    out of order.
 -- If job requests minimum and maximum node count range with select/cons_res,
    try to satisfy the higher value (formerly only allocated the minimum).
 -- Fix for checking for a non-existant job when querying steps.
 -- For job steps with the --exclusive option, base initial wait time in 
    partly upon the process ID for better performance with many job steps 
    started at the same time. Maintain exponential back-off as needed.
 -- Fix for correct step ordering in sview.
 -- Support optional argument to srun and salloc --immediate option. Specify
    timeout value in seconds for job or step to be allocated resources.

* Changes in SLURM 2.0.2
========================
 -- Fix, don't remove job details when a job is cancelled while pending.
 -- Do correct type for mktime so garbage isn't returned on 64bit systems 
    for accounting archival.
 -- Better checking in sacctmgr to avoid infinite loops.
 -- Fix minor memory leak in fake_slurm_step_layout_create()
 -- Fix node weight (scheduling priority) calculation for powered down
    nodes. Patch from Hongjia Cao, NUDT.
 -- Fix node suspend/resume rate calculations. Patch from Hongjia Cao, NUDT.
 -- Change calculations using ResumeRate and SuspendRate to provide higher
    resolution.
 -- Log the IP address for incoming messages having an invalid protocol 
    version number.
 -- Fix for sacct to show jobs that start the same second as the sacct
    command is issued.
 -- BLUEGENE - Fix for -n option to work on correct cpu counts for each 
    midplane instead of treating -n as a c-node count.
 -- salloc now sets SLURM_NTASKS_PER_NODE if --ntasks-per-node option is set.
 -- Fix select/linear to properly set a job's count of allocated processors
    (all processors on the allocated nodes).
 -- Fix select/cons_res to allocate proper CPU count when --ntasks-per-node
    option is used without a task count in the job request.
 -- Insure that no node is allocated to a job for which the CPU count is less
    than --ntasks-per-node * --cpus-per-task.
 -- Correct AllocProcs reported by "scontrol show node" when ThreadsPerCore
    is greater than 1 and select/cons_res is used.
 -- Fix scontrol show config for accounting information when values are 
    not set in the slurm.conf.
 -- Added a set of SBATCH_CPU_BIND* and SBATCH_MEM_BIND* env variables to keep
    jobsteps launched from within a batch script from inheriting the CPU and
    memory affinity that was applied to the batch script. Patch from Matthieu
    Hautreux, CEA.
 -- Ignore the extra processors on a node above configured size if either 
    sched/gang or select/cons_res is configured.
 -- Fix bug in tracking memory allocated on a node for select/cons_res plugin.
 -- Fixed a race condition when writing labelled output with a file per task
    or per node, which potentially closed a file before all data was written.
 -- BLUEGENE - Fix, for if a job comes in spanning both less than and 
    over 1 midplane in size we check the connection type appropriately.
 -- Make sched/backfill properly schedule jobs with constraints having node 
    counts. NOTE: Backfill of jobs with constraings having exclusive OR 
    operators are not fully supported.  
 -- If srun is cancelled by SIGINT, set the job state to cancelled, not 
    failed.
 -- BLUEGENE - Fix, for if you are setting an subbp into an error mode 
    where the subbp stated isn't the first ionode in a nodecard.
 -- Fix for backfill to not core when checking shared nodes.
 -- Fix for scontrol to not core when hitting just return in interactive mode.
 -- Improve sched/backfill logic with respect to shared nodes (multiple jobs
    per node).
 -- In sched/wiki (Maui interface) add job info fields QOS, RCLASS, DMEM and
    TASKSPERNODE. Patch from Bjorn-Helge Mevik, University of Oslo.

* Changes in SLURM 2.0.1
========================
 -- Fix, truncate time of start and end for job steps in sacct.
 -- Initialize all messages to slurmdbd. Previously uninitialized string could
    cause slurmctld to fail with invalid memory reference.
 -- BLUEGENE - Fix, for when trying to finish a torus on a block already 
    visited.  Even though this may be possible electrically this isn't valid
    in the under lying infrastructure.
 -- Fix, in mysql plugins change mediumints to int to support full 32bit 
    numbers.
 -- Add sinfo node state filtering support for NO_RESPOND, POWER_SAVE, FAIL, 
    MAINT, DRAINED and DRAINING states. The state filter of DRAIN still maps
    to any node in either DRAINED or DRAINING state.
 -- Fix reservation logic when job requests specific nodes that are already
    in some reservation the job can not use.
 -- Fix recomputation of a job's end time when allocated nodes which are
    being powered up. The end time would be set in the past if the job's
    time limit was INFINITE, resulting in it being prematurely terminated.
 -- Permit regular user to change the time limit of his pending jobs up to
    the partition's limit.
 -- Fix "-Q" (quiet) option for salloc and sbatch which was previously 
    ignored.
 -- BLUEGENE - fix for finding odd shaped blocks in dynamic mode.
 -- Fix logic supporting SuspendRate and ResumeRate configuration parameters.
    Previous logic was changing state of one too many nodes per minute.
 -- Save new reservation state file on shutdown (even if no changes).
 -- Fix, when partitions are deleted the sched and select plugins are notified.
 -- Fix for slurmdbd to create wckeyid's when they don't exist
 -- Fix linking problem that prevented checkpoint/aix from working.

* Changes in SLURM 2.0.0
========================
 -- Fix for bluegene systems to be able to create 32 node blocks with only 
    16 psets defined in dynamic layout mode.
 -- Improve srun_cr handling of child srun forking. Patch from Hongjia Cao, 
    NUDT.
 -- Configuration parameter ResumeDelay replaced by SuspendTimeout and 
    ResumeTimeout.
 -- BLUEGENE - sview/sinfo now displays correct cnode numbers for drained nodes
    or blocks in error state.
 -- Fix some batch job launch bugs when powering up suspended nodes.
 -- Added option '-T' for sacct to truncate time of start and end and set
    default of --starttime to Midnight of current day.

* Changes in SLURM 2.0.0-rc2
============================
 -- Change fanout logic to start on calling node instead of first node in 
    message nodelist.
 -- Fix bug so that smap builds properly on Sun Constellation system.
 -- Filter white-space out from node feature specification.
 -- Fixed issue with duration not being honored when updating start time in 
    reservations.
 -- Fix bug in sched/wiki and sched/wiki2 plugins for reporting job resource
    allocation properly when node names are configured out of sort order 
    with more than one numeric suffix (e.g. "tux10-1" is configured after 
    "tux5-1").
 -- Avoid re-use of job_id (if specified at submit time) when the existing
    job is in completing state (possible race condition with Moab).
 -- Added SLURM_DISTRIBUTION to env for salloc.
 -- Add support for "scontrol takeover" command for backup controller to 
    assume control immediately. Patch from Matthieu Hautreux, CEA.
 -- If srun is unable to communicate with the slurmd tasks are now marked as 
    failed with the controller.
 -- Fixed issues with requeued jobs not being accounted for correctly in 
    the accounting.
 -- Clear node's POWER_SAVE flag if configuration changes to one lacking a
    ResumeProgram.
 -- Extend a job's time limit as appropriate due to delays powering up nodes.
 -- If sbatch is used to launch a job step within an existing allocation (as
    used by LSF) and the required node is powered down, print the message
    "Job step creation temporarily disabled, retrying", sleep, and retry.
 -- Configuration parameter ResumeDelay added to control how much time must 
    after a node has been suspended before resume it (e.g. powering it back 
    up).
 -- Fix CPU binding for batch program. Patch from Matthieu Hautreux, CEA.
 -- Fix for front end systems non-responding nodes now show up correctly in
    sinfo.

* Changes in SLURM 2.0.0-rc1
============================
 -- Fix bug in preservation of advanced reservations when slurmctld restarts.
 -- Updated perlapi to match correctly with slurm.h structures
 -- Do not install the srun command on BlueGene systems (mpirun must be used to
    launch tasks).
 -- Corrections to scheduling logic for topology/tree in configurations where 
    nodes are configured in multiple leaf switches.
 -- Patch from Matthieu Hautreux for backup mysql deamon support.
 -- Changed DbdBackup to DbdBackupHost for slurmdbd.conf file
 -- Add support for spank_strerror() function and improve error handling in
    general for SPANK plugins.
 -- Added configuration parameter SrunIOTimeout to optionally ping srun's tasks
    for better fault tolerance (e.g. killed and restarteed SLURM daemons on 
    compute node).
 -- Add slurmctld and slurmd binding to appropriate communications address
    based upon NodeAddr, ControllerAddr and BackupAddr configuration 
    parameters. Based upon patch from Matthieu Hautreux, CEA.
    NOTE: Fails when SlurmDBD is configured with some configurations.
    NOTE: You must define BIND_SPECIFIC_ADDR to enable this option.
 -- Avoid using powered down nodes when scheduling work if possible. 
    Fix possible invalid memory reference in power save logic.

* Changes in SLURM 1.4.0-pre13
==============================
 -- Added new partition option AllocNodes which controls the hosts from 
    which jobs can be submitted to this partition. From Matthieu Hautreux, CEA.
 -- Better support the --contiguous option for job allocations.
 -- Add new scontrol option: show topology (reports contents of topology.conf 
    file via RPC if topology/tree plugin is configured).
 -- Add advanced reservation display to smap command.
 -- Replaced remaining references to SLURM_JOBID with SLURM_JOB_ID - except
    when needed for backwards compatibility.
 -- Fix logic to properly excise a DOWN node from the allocation of a job
    with the --no-kill option.
 -- The MySQL and PgSQL plugins for accounting storage and job completion are
    now only built if the underlying database libraries exists (previously
    the plugins were built to produce a fatal error when used).
 -- BLUEGENE - scontrol show config will now display bluegene.conf information.

* Changes in SLURM 1.4.0-pre12
==============================
 -- Added support for hard time limit by associations with added configuration 
    option PriorityUsageResetPeriod. This specifies the interval at which to 
    clear the record of time used. This is currently only available with the 
    priority/multifactor plugin.
 -- Added SLURM_SUBMIT_DIR to sbatch's output environment variables.
 -- Backup slurmdbd support implemented.
 -- Update to checkpoint/xlch logic from Hongjia Cao, NUDT.
 -- Added configuration parameter AccountingStorageBackupHost.

* Changes in SLURM 1.4.0-pre11
==============================
 -- Fix slurm.spec file for RPM build.

* Changes in SLURM 1.4.0-pre10
==============================
 -- Critical bug fix in task/affinity when the CoresPerSocket is greater
    than the ThreadsPerCore (invalid memory reference).
 -- Add DebugFlag parameter of "Wiki" to log sched/wiki and wiki2 
    communications in greater detail.
 -- Add "-d <slurmstepd_path>" as an option to the slurmd daemon to
    specifying a non-stardard slurmstepd file, used  for testing purposes.
 -- Minor cleanup to crypto/munge plugin.
    - Restrict uid allowed to decode job credentials in crypto/munge
    - Get slurm user id early in crypto/munge
    - Remove buggy error code handling in crypto/munge
 -- Added sprio command - works only with the priority/multifactor plugin
 -- Add real topology plugin infrastructure (it was initially added 
    directly into slurmctld code). To specify topology information,
    set TopologyType=topology/tree and add configuration information
    to a new file called topology.conf. See "man topology.conf" or
    topology.html web page for details.
 -- Set "/proc/self/oom_adj" for slurmd and slurmstepd daemons based upon
    the values of SLURMD_OOM_ADJ and SLURMSTEPD_OOM_ADJ environment 
    variables. This can be used to prevent daemons being killed when
    a node's memory is exhausted. Based upon patch by Hongjia  Cao, NUDT.
 -- Fix several bugs in task/affinity: cpuset logic was broken and 
    --cpus-per-task option not properly handled.
 -- Ensure slurmctld adopts SlurmUser GID as well as UID on startup.

* Changes in SLURM 1.4.0-pre9
=============================
 -- OpenMPI users only: Add srun logic to automatically recreate and 
    re-launch a job step if the step fails with a reserved port conflict.
 -- Added TopologyPlugin configuration parameter.
 -- Added switch topology data structure to slurmctld (for use by select 
    plugin) add load it based upon new slurm.conf parameters: SwitchName, 
    Nodes, Switches and LinkSpeed.
 -- Modify select/linear and select/cons_res plugins to optimize resource
    allocation with respect to network topology.
 -- Added  support for new configuration parameter EpilogSlurmctld (executed 
    by slurmctld daemon).
 -- Added checkpoint/blcr plugin, SLURM now support job checkpoint/restart 
    using BLCR. Patch from Hongjia Cao, NUDT, China.
 -- Made a variety of new environment variables available to PrologSlurmctld
    and EpilogSlurmctld. See the "Prolog and Epilog Scripts" section of the 
    slurm.conf man page for details.
 -- NOTE: Cold-start (without preserving state) required for upgrade from 
    version 1.4.0-pre8.

* Changes in SLURM 1.4.0-pre8
=============================
 -- In order to create a new partition using the scontrol command, use
    the "create" option rather than "update" (which will only operate
    upon partitions that already exist).
 -- Added environment variable SLURM_RESTART_COUNT to batch jobs to
    indicated the count of job restarts made.
 -- Added sacctmgr command "show config".
 -- Added the scancel option --nodelist to cancel any jobs running on a
    given list of nodes.
 -- Add partition-specific DefaultTime (default time limit for jobs, 
    if not specified use MaxTime for the partition. Patch from Par
    Andersson, National Supercomputer Centre, Sweden.
 -- Add support for the scontrol command to be able change the Weight
    associated with nodes. Patch from Krishnakumar Ravi[KK] (HP).
 -- Add DebugFlag configuration option of "CPU_Bind" for detailed CPU
    binding information to be logged.
 -- Fix some significant bugs in task binding logic (possible infinite loops
    and memory corruption).
 -- Add new node state flag of NODE_STATE_MAINT indicating the node is in
    a reservation of type MAINT.
 -- Modified task/affinity plugin to automatically bind tasks to sockets,
    cores, or threads as appropriated based upon resource allocation and
    task count. User can override with srun's --cpu_bind option. 
 -- Fix bug in backfill logic for select/cons_res plugin, resulted in 
    error "cons_res:_rm_job_from_res: node_state mis-count".
 -- Add logic go bind a batch job to the resources allocated to that job.
 -- Add configuration parameter MpiParams for (future) OpenMPI port 
    management. Add resv_port_cnt and resv_ports fields to the job step 
    data structures. Add environment variable SLURM_STEP_RESV_PORTS to
    show what ports are reserved for a job step.
 -- Add support for SchedulerParameters=interval=<sec> to control the time
    interval between executions of the backfill scheduler logic.
 -- Preserve record of last job ID in use even when doing a cold-start unless
    there is no job state file or there is a change in its format (which only 
    happens when there is a change in SLURM's major or minor version number: 
    v1.3 -> v1.4).
 -- Added new configuration parameter KillOnBadExit to kill a job step as soon
    as any task of a job step exits with a non-zero exit code. Patch based
    on work from Eric Lin, Bull.
 -- Add spank plugin calls for use by salloc and sbatch command, see 
    "man spank" for details.
 -- NOTE: Cold-start (without preserving state) required for upgrade from 
    version 1.4.0-pre7.

* Changes in SLURM 1.4.0-pre7
=============================
 -- Bug fix for preemption with select/cons_res when there are no idle nodes.
 -- Bug fix for use of srun options --exclusive and --cpus-per-task together
    for job step resource allocation (tracking of cpus in use was bad).
 -- Added the srun option --preserve-env to pass the current values of 
    environment variables SLURM_NNODES and SLURM_NPROCS through to the 
    executable, rather than computing them from commandline parameters.
 -- For select/cons_res or sched/gang only: Validate a job's resource 
    allocation socket and core count on each allocated node. If the node's
    configuration has been changed, then abort the job.
 -- For select/cons_res or sched/gang only: Disable updating a node's 
    processor count if FastSchedule=0. Administrators must set a valid
    processor count although the memory and disk space configuration can
    be loaded from the compute node when it starts.
 -- Add configure option "--disable-iso8601" to disable SLURM use of ISO 8601
    time format at the time of SLURM build. Default output for all commands
    is now ISO 8601 (yyyy-mm-ddThh:mm:ss).
 -- Add support for scontrol to explicity power a node up or down using the
    configured SuspendProg and ResumeProg programs.
 -- Fix book select/cons_res logic for tracking the number of allocated
    CPUs on a node when a partition's Shared value is YES or FORCE.
 -- Added configure options "--enable-cray-xt" and "--with-apbasil=PATH" for
    eventual support of Cray-XT systems.

* Changes in SLURM 1.4.0-pre6
=============================
 -- Fix job preemption when sched/gang and select/linear are configured with
    non-sharing partitions.
 -- In select/cons_res insure that required nodes have available resources.

* Changes in SLURM 1.4.0-pre5
=============================
 -- Correction in setting of SLURM_CPU_BIND environment variable.
 -- Rebuild slurmctld's job select_jobinfo->node_bitmap on restart/reconfigure
    of the daemon rather than restoring the bitmap since the nodes in a system
    can change (be added or removed).
 -- Add configuration option "--with-cpusetdir=PATH" for non-standard 
    locations.
 -- Get new multi-core data structures working on BlueGene systems.
 -- Modify PMI_Get_clique_ranks() to return an array of integers rather 
    than a char * to satisfy PMI standard. Correct logic in 
    PMI_Get_clique_size() for when srun --overcommit option is used.
 -- Fix bug in select/cons_res, allocated a job all of the processors on a 
    node when the --exclusive option is specified as a job submit option.
 -- Add NUMA cpu_bind support to the task affinity plugin. Binds tasks to
    a set of CPUs that belong NUMA locality domain with the appropriate
    --cpu-bind option (ldoms, rank_ldom, map_ldom, and mask_ldom), see
    "man srun" for more information.

* Changes in SLURM 1.4.0-pre4
=============================
 -- For task/affinity, force jobs to use a particular task binding by setting
    the TaskPluginParam configuration parameter rather than slurmd's
    SLURM_ENFORCED_CPU_BIND environment variable.
 -- Enable full preemption of jobs by partition with select/cons_res 
    (cons_res_preempt.patch from Chris Holmes, HP).
 -- Add configuration parameter DebugFlags to provide detailed logging for
    specific subsystems (steps and triggers so far).
 -- srun's --no-kill option is passed to slurmctld so that a job step is 
    killed even if the node where srun executes goes down (unless the 
    --no-kill option is used, previous termination logic would fail if 
    srun was not responding).
 -- Transfer a job step's core bitmap from the slurmctld to the slurmd
    within the job step credential.
 -- Add cpu_bind, cpu_bind_type, mem_bind and mem_bind_type to job allocation
    request and job_details structure in slurmctld. Add support to --cpu_bind
    and --mem_bind options from salloc and sbatch commands.

* Changes in SLURM 1.4.0-pre3
=============================
 -- Internal changes: CPUs per node changed from 32-bit to 16-bit size.
    Node count fields changed from 16-bit to 32-bit size in some structures.
 -- Remove select plugin functions select_p_get_extra_jobinfo(),
    select_p_step_begin() and select_p_step_fini().
 -- Remove the following slurmctld job structure fields: num_cpu_groups,
    cpus_per_node, cpu_count_reps, alloc_lps_cnt, alloc_lps, and used_lps.
    Use equivalent fields in new "select_job" structure, which is filled
    in by the select plugins.
 -- Modify mem_per_task in job step request from 16-bit to 32-bit size.
    Use new "select_job" structure for the job step's memory management.
 -- Add core_bitmap_job to slurmctld's job step structure to identify
    which specific cores are allocated to the step.
 -- Add new configuration option OverTimeLimit to permit jobs to exceed 
    their (soft) time limit by a configurable amount. Backfill scheduling
    will be based upon the soft time limit.
 -- Remove select_g_get_job_cores(). That data is now within the slurmctld's
    job structure.

* Changes in SLURM 1.4.0-pre2
=============================
 -- Remove srun's --ctrl-comm-ifhn-addr option (for PMI/MPICH2). It is no
    longer needed.
 -- Modify power save mode so that nodes can be powered off when idle. See
    https://computing.llnl.gov/linux/slurm/power_save.html or 
    "man slurm.conf" (SuspendProgram and related parameters) for more 
    information.
 -- Added configuration parameter PrologSlurmctld, which can be used to boot
    nodes into a particular state for each job. See "man slurm.conf" for 
    details.
 -- Add configuration parameter CompleteTime to control how long to wait for 
    a job's completion before allocating already released resources to pending
    jobs. This can be used to reduce fragmentation of resources. See
    "man slurm.conf" for details.
 -- Make default CryptoType=crypto/munge. OpenSSL is now completely optional.
 -- Make default AuthType=auth/munge rather than auth/none.
 -- Change output format of "sinfo -R" from "%35R %N" to "%50R %N".

* Changes in SLURM 1.4.0-pre1
=============================
 -- Save/restore a job's task_distribution option on slurmctld retart.
    NOTE: SLURM must be cold-started on converstion from version 1.3.x.
 -- Remove task_mem from job step credential (only job_mem is used now).
 -- Remove --task-mem and --job-mem options from salloc, sbatch and srun
    (use --mem-per-cpu or --mem instead).
 -- Remove DefMemPerTask from slurm.conf (use DefMemPerCPU or DefMemPerNode
    instead).
 -- Modify slurm_step_launch API call. Move launch host from function argument
    to element in the data structure slurm_step_launch_params_t, which is
    used as a function argument.
 -- Add state_reason_string to job state with optional details about why
    a job is pending.
 -- Make "scontrol show node" output match scontrol input for some fields
    ("Cores" changed to "CoresPerSocket", etc.).
 -- Add support for a new node state "FUTURE" in slurm.conf. These node records
    are created in SLURM tables for future use without a reboot of the SLURM
    daemons, but are not reported by any SLURM commands or APIs.

* Changes in SLURM 1.3.17
=========================
 -- Fix bug in configure script that can clear user specified LIBS.

* Changes in SLURM 1.3.16
=========================
 -- Fix memory leak in forward logic of tree message passing.
 -- Fix job exit code recorded for srun job allocation.
 -- Bluegene - Bug fix for too many parameters being passed to a debug statement
 -- Bluegene - Bug fix for systems running more than 8 in the X dim running
    Dynamic mode.

* Changes in SLURM 1.3.15
=========================
 -- Fix bug in squeue command with sort on job name ("-S j" option) for jobs
    that lack a name. Previously generated an invalid memory reference.
 -- Permit the TaskProlog to write to the job's standard output by writing
    a line containing the prefix "print " to it's standard output.
 -- Fix for making the slurmdbd agent thread start up correctly when 
    stopped and then started again.
 -- Add squeue option to report jobs by account (-U or --account). Patch from
    Par Andersson, National Supercomputer Centre, Sweden.
 -- Add -DNUMA_VERSION1_COMPATIBILITY to Makefile CFLAGS for proper behavior
    when building with NUMA version 2 APIs.
 -- BLUEGENE - slurm works on a BGP system.
 -- BLUEGENE - slurm handles HTC blocks
 -- BLUEGENE - Added option DenyPassthrough in the bluegene.conf.  Can be set
    to any combination of X,Y,Z to not allow passthroughs when running in 
    dynamic layout mode.
 -- Fix bug in logic to remove a job's dependency, could result in abort.
 -- Add new error message to sched/wiki and sched/wiki2 (Maui and Moab) for
    STARTJOB request: "TASKLIST includes non-responsive nodes".
 -- Fix bug in select/linear when used with sched/gang that can result in a 
    job's required or excluded node specification being ignored.
 -- Add logic to handle message connect timeouts (timed-out.patch from 
    Chuck Clouston, Bull).
 -- BLUEGENE - CFLAGS=-m64 is no longer required in configure
 -- Update python-hostlist code from Kent Engström (NSC) to v1.5
    - Add hostgrep utility to search for lines matching a hostlist.
    - Make each "-" on the command line count as one hostlist argument.
      If multiple hostslists are given on stdin they are combined to a
      union hostlist before being used in the way requested by the
      options.
 -- When using -j option in sacct no user restriction will applied unless
    specified with the -u option.
 -- For sched/wiki and sched/wiki2, change logging of wiki message traffic
    from debug() to debug2(). Only seen if SlurmctldDebug is configured to
    6 or higher.
 -- Significant speed up for association based reports in sreport
 -- BLUEGENE - fix for checking if job can run with downed nodes.  Previously 
    sbatch etc would tell you node configuration not available now jobs are 
    accepted but held until nodes are back up.
 -- Fix in accounting so if any nodes are removed from the system when they 
    were previously down will be recorded correctly.
 -- For sched/wiki2 (Moab), add flag to note if job is restartable and
    prevent deadlock of job requeue fails.
 -- Modify squeue to return non-zero exit code on failure. Patch from
    Par Andersson (NSC).
 -- Correct logic in select/cons_res to allocate a job the maximum node
    count from a range rather than minimum (e.g. "sbatch -N1-4 my.sh").
 -- In accounting_storage/filetxt and accounting_storage/pgsql fix 
    possible invalid memory reference when a job lacks a name.
 -- Give srun command an exit code of 1 if the prolog fails.
 -- BLUEGENE - allows for checking nodecard states in the system instead 
    of midplane state so as to not down an entire midplane if you don't 
    have to.
 -- BLUEGENE - fix creation of MESH blocks 
 -- BLUEGENE - on job cancellation we call jm_cancel_job and then wait until
    the system cleans up the job.  Before we would send a SIGKILL right 
    at the beginning. 
 -- BLUEGENE - if a user specifies a node count that can not be met the job 
    will be refused instead of before the plugin would search for the next 
    larger size that could be created.  This prevents users asking for 
    things that can't be created, and then getting something back they might 
    not be expecting.

* Changes in SLURM 1.3.14
=========================
 -- SECURITY BUG: Fix in sbcast logic that permits users to write files based
    upon supplimental groups of the slurmd daemon. Similar logic for event
    triggers if slurmctld is run as user root (not typical).

* Changes in SLURM 1.3.13
=========================
 -- Added ability for slurmdbd to archive and purge step and/or job records.
 -- Added DefaultQOS as an option to slurmdbd.conf for when clusters are 
    added the default will be set to this if none is given in the sacctmgr line.
 -- Added configure option --enable-sun-const for Sun Constellation system with
    3D torus interconnect. Supports proper smap and sview displays for 3-D
    topology. Node names are automatically put into Hilbert curve order given
    a one-line nodelist definition in slurm.conf (e.g. NodeNames=sun[000x533]). 
 -- Fixed bug in parsing time for sacct and sreport to pick the correct year if
    none is specified.
 -- Provide better scheduling with overlapping partitions (when a job can not
    be scheduled due to insufficient resources, reserve specific the nodes
    associated with that partition rather than blocking all partitions with
    any overlapping nodes).
 -- Correct logic to log in a job's stderr that it was "CANCELLED DUE TO 
    NODE FAILURE" rather than just "CANCELLED".
 -- Fix to crypto/openssl plugin that could result in job launch requests
    being spoofed through the use of an improperly formed credential. This bug 
    could permit a user to launch tasks on compute nodes not allocated for 
    their use, but will NOT permit them to run tasks as another user. For more 
    information see http://www.ocert.org/advisories/ocert-2008-016.html

* Changes in SLURM 1.3.12
=========================
 -- Added support for Workload Characteristic Key (WCKey) in accounting.  The
    WCkey is something that can be used in accounting to group associations
    together across clusters or within clusters that are not related.  Use 
    the --wckey option in srun, sbatch or salloc or set the SLURM_WCKEY env
    var to have this set. Use sreport with the wckey option to view reports.
    THIS CHANGES THE RPC LEVEL IN THE SLURMDBD.  YOU MUST UPGRADE YOUR SLURMDBD
    BEFORE YOU UPGRADE THE REST OF YOUR CLUSTERS.  THE NEW SLURMDBD WILL TALK 
    TO OLDER VERSIONS OF SLURM FINE.
 -- Added configuration parameter BatchStartTimeout to control how long to 
    allow for a batch job prolog and environment loading (for Moab) to run.
    Previously if job startup took too long, a batch job could be cancelled
    before fully starting with a SlurmctldLog message of "Master node lost 
    JobId=#, killing it".  See "man slurm.conf" for details.
 -- For a job step, add support for srun's --nodelist and --exclusive options
    to be used together.
 -- On slurmstepd failure, set node state to DRAIN rather than DOWN.
 -- Fix bug in select/cons_res that would incorrectly satify a tasks's
    --cpus-per-task specification by allocating the task CPUs on more than
    one node.
 -- Add support for hostlist expressions containing up to two numeric 
    expressions (e.g. "rack[0-15]_blade[0-41]").
 -- Fix bug in slurmd message forwarding which left file open in the case of
    some communication failures.
 -- Correction to sinfo node state information on BlueGene systems. DRAIN
    state was replaced with ALLOC or IDLE under some situations.
 -- For sched/wiki2 (Moab), strip quotes embedded within job names from the
    name reported.
 -- Fix bug in jobcomp/script that could cause the slurmctld daemon to exit
    upon reconfiguration ("scontrol reconfig" or SIGHUP).
 -- Fix to sinfo, don't print a node's memory size or tmp_disk space with 
    suffix of "K" or "M" (thousands or millions of megabytes).
 -- Improve efficiency of scheduling jobs into partitions which do not overlap.
 -- Fixed sreport user top report to only display the limit specified 
    instead of all users.

* Changes in SLURM 1.3.11
=========================
 -- Bluegene/P support added (minimally tested, but builds correctly).
 -- Fix infinite loop when using accounting_storage/mysql plugin either from
    the slurmctld or slurmdbd daemon.
 -- Added more thread safety for assoc_mgr in the controller.
 -- For sched/wiki2 (Moab), permit clearing of a job's dependencies with the 
    JOB_MODIFY option "DEPEND=0".
 -- Do not set a running or pending job's EndTime when changing it's time 
    limit.
 -- Fix bug in use of "include" parameter within the plugstack.conf file.
 -- Fix bug in the parsing of negative numeric values in configuration files.
 -- Propagate --cpus-per-task parameter from salloc or sbatch input line to
    the SLURM_CPUS_PER_TASK environment variable in the spawned shell for 
    srun to use.
 -- Add support for srun --cpus-per-task=0. This can be used to spawn tasks
    without allocating resouces for the job step from the job's allocation
    when running multiple job steps with the --exclusive option.
 -- Remove registration messages from saved messages when bringing down cluster.
    Without causes deadlock if wrong cluster name is given.
 -- Correction to build for srun debugger (export symbols).
 -- sacct will now display more properly allocations made with salloc with only 
    one step.
 -- Altered sacctmgr, sreport to look at complete option before applying. 
    Before we would only look at the first determined significant characters.
 -- BLUGENE - in overlap mode marking a block to error state will now end
    jobs on overlapping blocks and free them.
 -- Give a batch job 20 minutes to start before considering it missing and 
    killing it (long delay could result from slurmd being paged out). Changed
    the log message from "Master node lost JobId=%u, killing it" to "Batch 
    JobId=%u missing from master node, killing it".
 -- Avoid "Invalid node id" error when a job step within an existing job 
    allocation specifies a node count which is less than the node count
    allocated in order to satisfy the task count specification (e.g. 
    "srun -n16 -N1 hostname" on allocation of 16 one-CPU nodes).
 -- For sched/wiki2 (Moab) disable changing a job's name after it has begun
    execution.

* Changes in SLURM 1.3.10
=========================
 -- Fix several bugs in the hostlist functions:
    - Fix hostset_insert_range() to do proper accounting of hl->nhosts (count).
    - Avoid assertion failure when callinsg hostset_create(NULL).
    - Fix return type of hostlist and hostset string functions from size_t to
      ssize_t.
    - Add check for NULL return from hostlist_create().
    - Rewrite of hostrange_hn_within(), avoids reporting "tst0" in the hostlist
      "tst".
 -- Modify squeue to accept "--nodes=<hostlist>" rather than 
    "--node=<node_name>" and report all jobs with any allocated nodes from set
    of nodes specified. From Par Anderson, National Supercomputer Centre, 
    Sweden.
 -- Fix bug preventing use of TotalView debugger with TaskProlog configured or 
    or srun's --task-prolog option.
 -- Improve reliability of batch job requeue logic in the event that the slurmd
    daemon is temporarily non-responsive (for longer than the configured
    MessageTimeout value but less than the SlurmdTimeout value).
 -- In sched/wiki2 (Moab) report a job's MAXNODES (maximum number of permitted
    nodes).
 -- Fixed SLURM_TASKS_PER_NODE to live up more to it's name on an allocation. 
    Will now contain the number of tasks per node instead of the number of CPUs
    per node.  This is only for a resource allocation. Job steps already have 
    the environment variable set correctly.
 -- Configuration parameter PropagateResourceLimits has new option of "NONE".
 -- User's --propagate options take precidence over PropagateResourceLimits
    configuration parameter in both srun and sbatch commands.
 -- When Moab is in use (salloc or sbatch is executed with the --get-user-env
    option to be more specific), load the user's default resource limits rather
    than propagating the Moab daemon's limits.
 -- Fix bug in slurmctld restart logic for recovery of batch jobs that are
    initiated as a job step rather than an independent job (used for LSF).
 -- Fix bug that can cause slurmctld restart to fail, bug introduced in SLURM
    version 1.3.9. From Eygene Ryabinkin, Kurchatov Institute, Russia.
 -- Permit slurmd configuration parameters to be set to new values from 
    previously unset values.

* Changes in SLURM 1.3.9
========================
 -- Fix jobs being cancelled by ctrl-C to have correct cancelled state in 
    accounting.
 -- Slurmdbd will only cache user data, made for faster start up
 -- Improved support for job steps in FRONT_END systems
 -- Added support to dump and load association information in the controller
    on start up if slurmdbd is unresponsive
 -- BLUEGENE - Added support for sched/backfill plugin
 -- sched/backfill modified to initiate multiple jobs per cycle.
 -- Increase buffer size in srun to hold task list expressions. Critical 
    for jobs with 16k tasks or more.
 -- Added support for eligible jobs and downed nodes to be sent to accounting
    from the controller the first time accounting is turned on.
 -- Correct srun logic to support --tasks-per-node option without task count.
 -- Logic in place to handle multiple versions of RPCs within the slurmdbd. 
    THE SLURMDBD MUST BE UPGRADED TO THIS VERSION BEFORE UPGRADING THE 
    SLURMCTLD OR THEY WILL NOT TALK.  
    Older versions of the slurmctld will continue to talk to the new slurmdbd.