- 11 Mar, 2019 20 commits
-
-
Tim Wickberg authored
Used to select between different authentication plugins.
-
Tim Wickberg authored
Identifies which authentication plugin (as identified by the index rather than the plugin_id) was used to decode this specific credential. Needed so that code paths responding to this message can reply with the same authentication type to ensure the message can be accepted by the remote (which, except for the slurmctld/slurmdbd, will always be a single plugin type.
-
Tim Wickberg authored
-
Tim Wickberg authored
Standardize on DEFUNCT_RPC_#### for numbers that are reusable. Or DBD_DEFUNCT_RPC_#### in slurmdbd_defs.h.
-
Tim Wickberg authored
The 19.05 release is the second after 17.11, so we no longer need this.
-
Tim Wickberg authored
These were all missing a copy of msg->conn into the response_msg, which implies they were broken for persistent connections before this.
-
Tim Wickberg authored
This also catches a number of locations where flags were not being propogated across to the response.
-
Tim Wickberg authored
-
Tim Wickberg authored
Two of the three functions have different names, and even if translated to the current terms this isn't a typical use.
-
Tim Wickberg authored
-
Tim Wickberg authored
Plugins do not and should not keep pointers in to buf.
-
Tim Wickberg authored
-
Tim Wickberg authored
-
Tim Wickberg authored
And update all calling locations. Note that this removes a lot of unnecessary calls to slurm_get_auth_info() which should serve as a slight performance speedup.
-
Tim Wickberg authored
Now unused. This info should only be needed at verification time, which must happen before any slurm_auth_get_*() calls.
-
Tim Wickberg authored
-
Tim Wickberg authored
-
Morris Jette authored
bug 6646
-
Morris Jette authored
-
Morris Jette authored
Insure that each MPS server has a single/common percentage of a GPU
-
- 09 Mar, 2019 3 commits
-
-
Morris Jette authored
Add module to the Makefiles Add test description to README (used for logging to stderr) If "date" fails and an error (FAILURE) is logged, then make the test have an exit 1 If the test can not run due to configuration then do not log as a failure and exit 0
-
Morris Jette authored
Coverity CID 195594
-
Morris Jette authored
Coverity CID 195725
-
- 08 Mar, 2019 17 commits
-
-
Tim Wickberg authored
-
Broderick Gardner authored
Bug 6633.
-
Morris Jette authored
Coverity CID 195599
-
Morris Jette authored
Coverity CID 195608
-
Morris Jette authored
Coverity CID 195595
-
Morris Jette authored
Coverity CID 195595
-
Morris Jette authored
Coverity CID 195594
-
Morris Jette authored
Coverity CID 195603 and 195605
-
Morris Jette authored
Coverity CID 195610
-
Morris Jette authored
Coverity CID 195592
-
Morris Jette authored
Coverity CID 195593
-
Morris Jette authored
Coverity CID 195604
-
Morris Jette authored
Coverity CID 195609
-
Morris Jette authored
Coverity CID 195606
-
Morris Jette authored
Coverity CID 195598
-
Morris Jette authored
Coverity CID 187785
-
Tim Wickberg authored
Use slurm_seterrno(), rather than maintaining a plugin-local and credential local version of that errno. Remove g_slurm_auth_errno() and g_slurm_auth_errstr(). Replace all calling locations with %m format identifiers which should pick up the errno in that thread, which is now directly set by the auth plugin. The one place that this represents a slight regression in functionality is that we loose the specific EMUNGE errno values. However, the places that will set this in the auth/munge plugin are already printing it through an error() with munge_ctx_strerror(). Replace those two locations with ESLURM_AUTH_CRED_INVALID instead.
-