bg.properties in order for the runjob_mux to run correctly.

Signed-off-by: Danny Auble <da@schedmd.com>

but job is going to be canceled because it is interactive or other reason
it now receives the grace time.

check if a block is still makable if the cable wasn't in error.

removal of the job on the block failed.

29d79ef8

same time a block is destroyed and that block just happens to be the
smallest overlapping block over the bad hardware.

but not node count the node count is correctly figured out.

Without this fix, gang scheduling mode could start without creating
a list resulting in an assert when jobs are submitted.

packing the step layout structure.

we must use a small block instead of a shared midplane block.

still messages we find when we poll but haven't given it back to the real
time yet.

a job kill timeout aren't always reported to the system.  This is now
handled by the runjob_mux plugin.

sub-blocks.

to make a larger small block and are running with sub-blocks.

function didn't always work correctly.

the next step in the allocation only uses part of the allocation it gets
the correct cnodes.

In etc/init.d/slurm move check for scontrol after sourcing
/etc/sysconfig/slurm. Patch from Andy Wettstein, University of Chicago.

Change license option count separator from "*" to ":" for consistency with
the gres option (e.g. "--licenses=foo:2 --gres=gpu:2"). The "*" will still
be accepted, but is no longer documented.

maintain.

This change makes the code consistent with the documentation.
Note that "bf_res=" will continue to be recognized for now.
Patch from Rod Schultz, Bull.

I have implemented the changes as you suggested:   using a "-dd" option to indicate that the display of the script is wanted, and setting both the "SHOW_DETAIL" and a new "SHOW_DETAIL2" flag.

Since "scontrol" can be run interactively as well,  I added a new "script" option to indicate that display of both the script and the details is wanted if the job is a batch job.

Here are the man page updates for "man scontrol".   For the "-d, --details" option:

       -d, --details
              Causes  the  show command to provide additional details where available.  Repeating the option more than
              once (e.g., "-dd") will cause the show job command to also list the batch script, if the job was a batch
              job.

For the interactive "details" option:

       details
              Causes  the  show  command  to provide additional details where available.  Job information will include
              CPUs and NUMA memory allocated on each node.  Note that on computers  with  hyperthreading  enabled  and
              SLURM  configured  to allocate cores, each listed CPU represents one physical core.  Each hyperthread on
              that core can be allocated a separate task, so a job's CPU count and task count  may  differ.   See  the
              --cpu_bind  and  --mem_bind  option  descriptions  in  srun man pages for more information.  The details
              option is currently only supported for the show job command. To also list the  batch  script  for  batch
              jobs, in addition to the details, use the script option described below instead of this option.

And for the new interactive "script" option:

       script Causes the show job command to list the batch script for batch jobs in addition to the  detail  informa-
              tion described under the details option above.

Attached are the patch file for the changes and a text file with the results of the tests I did to check out the changes.   The patches are against SLURM 2.4.0-rc1.

        -Don Albert-

This change makes the code consistent with the documentation.
Note that "bf_res=" will continue to be recognized for now.
Patch from Rod Schultz, Bull.

I have implemented the changes as you suggested:   using a "-dd" option to indicate that the display of the script is wanted, and setting both the "SHOW_DETAIL" and a new "SHOW_DETAIL2" flag.

Since "scontrol" can be run interactively as well,  I added a new "script" option to indicate that display of both the script and the details is wanted if the job is a batch job.

Here are the man page updates for "man scontrol".   For the "-d, --details" option:

       -d, --details
              Causes  the  show command to provide additional details where available.  Repeating the option more than
              once (e.g., "-dd") will cause the show job command to also list the batch script, if the job was a batch
              job.

For the interactive "details" option:

       details
              Causes  the  show  command  to provide additional details where available.  Job information will include
              CPUs and NUMA memory allocated on each node.  Note that on computers  with  hyperthreading  enabled  and
              SLURM  configured  to allocate cores, each listed CPU represents one physical core.  Each hyperthread on
              that core can be allocated a separate task, so a job's CPU count and task count  may  differ.   See  the
              --cpu_bind  and  --mem_bind  option  descriptions  in  srun man pages for more information.  The details
              option is currently only supported for the show job command. To also list the  batch  script  for  batch
              jobs, in addition to the details, use the script option described below instead of this option.

And for the new interactive "script" option:

       script Causes the show job command to list the batch script for batch jobs in addition to the  detail  informa-
              tion described under the details option above.

Attached are the patch file for the changes and a text file with the results of the tests I did to check out the changes.   The patches are against SLURM 2.4.0-rc1.

        -Don Albert-

compiling with --enable-debug

The purpose of this is so moab scripts and commands (such as 'checkjob')
have consistent access to the SUBMITHOST variable.

isn't up at the time the slurmctld starts, not running the
priority/multifactor plugin, and then the database is started up later.

Format is "name:used/total"