- 07 Mar, 2019 15 commits
-
-
Tim Wickberg authored
-
Tim Wickberg authored
The plugin-specific errno handling these were intended for does not exist, and these ranges can be reused without issue at this point.
-
Tim Wickberg authored
-
Tim Wickberg authored
No plugins implement this interface, so discard.
-
Tim Wickberg authored
Never called. None of the plugins have bothered to implement this correctly. The jobcomp/script plugin comes closest, but did not pick error codes within the designated range.
-
Morris Jette authored
Remove "cons_tres: " from some src/common/gres.c log messages. They are vestigial from relocated functions.
-
Morris Jette authored
-
Morris Jette authored
This needs to be replaced by a finer-grained access control in the next pre-release of v19.05
-
Michael Hinton authored
Move tests into relevant FastSchedule groups. Rename tests based on FastSchedule setting. Tweak some expected output to match actual. Add capability for expected errors. Comment out some tests that still need work. Bug 6635
-
Michael Hinton authored
Bug 6635
-
Morris Jette authored
Triggered with GresTypes=gpu,mps. zero gpu count for node defined in slurm.conf and non-zero gpu count in gres.conf
-
Tim Wickberg authored
As libssh2 is gone, we no longer need x_ac_ssh2.m4. Add in x_ac_x11.m4 to restore the --disable-x11 option. Unconditionally build x11_forwarding.c now that it's no longer dependent on the libssh2 libraries being available.
-
Tim Wickberg authored
Bug 3647.
-
Tim Wickberg authored
Leave the state file name - burst_buffer_cray_state alone. Bug 6440.
-
Tim Wickberg authored
-
- 06 Mar, 2019 12 commits
-
-
Tim Wickberg authored
The order can change as long as it is kept in sync with the ops struct, which already notes this requirement.
-
Morris Jette authored
-
Nathan Rini authored
Reverts code added in 8486c97e to handle failure mode of BGQ jobs. Bug 6566.
-
Felip Moll authored
The int size may not be enough when converting from seconds to usec for the maximums defined for bf_interval. _yield_sleep has been to adapt to this change too. Bug 6401
-
Felip Moll authored
All numeric backfill parameters have now maximums and minimum values. Bug 6401
-
Felip Moll authored
-
Danny Auble authored
-
Morris Jette authored
Improve log and comments
-
Morris Jette authored
Set CUDA_VISIBLE_DEVICES and CUDA_MPS_ACTIVE_THREAD_PERCENTAGE environment variables in Prolog and Epilog for jobs requesting gres/mps. This can be used to start, terminate and otherwise manage mps servers for the user.
-
Morris Jette authored
Previous logic would drain node with less than configured gres. bug 6635
-
Danny Auble authored
This also removes the check for duplicates that seemed redundant. Bug 6635
-
Morris Jette authored
Without this change a single job could not use 100% of the gres/mps on any single device, but only up to one less than the total count.
-
- 05 Mar, 2019 13 commits
-
-
Morris Jette authored
bug 6635
-
Danny Auble authored
-
Morris Jette authored
Without this change, test19.18 would generate fatal errors due to using the Slurm APIs, but not having the same environment as the slurmctld
-
Danny Auble authored
as the parameter to determine how to gather gres/gpu configuration. bug 6635
-
Morris Jette authored
Commit 6ac4ce84 introduces a dependency in the gres plugin on the select plugin. Bug 6638.
-
Morris Jette authored
slurmstepd needed some changes to avoid creating a size zero bitmap. bug 6635
-
Danny Auble authored
If we do have 0 this means we have no gres on the node.
-
Danny Auble authored
Any other call to the bitstring will fail (bit_test, bit_clear, etc). I was unable to find a situation where this would be valid.
-
Michael Hinton authored
-
Felip Moll authored
Bug 6616
-
Tim Wickberg authored
-
Danny Auble authored
Bug 6612
-
Tim Wickberg authored
-